| Please Note: Setup Charges for Knuckles
A machining setup charge of $100 applies to all knuckles, however, if you order regular knuckles and special knuckles at the same time, only ONE setup charge will apply.
|
|
|
Knuckles
Custom machined to fit your tubing or pipe. Heat treated aluminum with hardened swing bolt, stainless steel pivot pins, and lock knob.
| Weight 2-1/2 lbs. (1.14 kg) |
| Bore Maximum 2" |
51 mm |
| Bore Minimum 1-5/8" |
42 mm |
Minimum setup charge applies.
| Cat. # |
Quantity |
Price |
| CC-9100 |
1-20 |
$75 each |
| CC-610A |
21 or more |
$65 each |
Back to Top
|
Swivel Knuckles
 Knuckles (as above) but with a swivel shank for drop arms used for low angle shots. Swivels 175 degrees. Note: price is for each knuckle. Two knuckles are shown as an example of typical application.
Minimum setup charge applies.
| Cat. # |
Price |
| CC-2220 |
$110 each |
Back to Top
|
Rotating Swivel Knuckles
Swivels 175 degrees like normal swivel knuckles, but in addition it rotates 360 degrees.
Minimum setup charge applies.
| Cat. # |
Price |
| CC-3230 |
$160 each |
Back to Top
|
"A" Frames
 Similar in use as the example above for Swivel Knuckles with three regular knuckles and tubing to fit your needs. Ready for use for low platforms or for mounting lights.
Note: A $50 packing charge will apply for shipping.
Minimum setup charge applies.
| Cat. # |
Price |
| CC-4240 |
$650 each |
Back to Top
|
Bridge Plate
Custom built to your required length and width. We now offer the "Hollywood" style bridge plate which is made up of two 1/4" (6 mm) aluminum plates welded on top and bottom of two 1-1/2" (3.8 cm) square tubes. Two widths (front to back) are available, 8-inch (20.3 cm) and 12-inch (30.5 cm). The length is made to fit your requirements. After welding, slots are machined in both the top and bottom plates for fastening to your camera car with bridge plate clamps.
Weights vary depending on length and width.
Note: a packing charge will apply. Bridge plates cannot be shipped by UPS.
| Cat. # |
|
Price |
| CC-1208 |
8" wide, 84" length (213 cm) |
$775 |
|
Lengths over 84" add $12 per inch (2.54 cm) |
| CC-1212 |
12" wide, 84" length (213 cm) |
$995 |
|
Lengths over 84" add $15 per inch (2.54 cm) |
Back to Top
|
Bridge Plate Locking Clamp
Cast aluminum with forged swing bolt and aluminum lock knob.
Weight 4 lbs. (1.8 kg)
| Cat. # |
Price |
| CC-2310 |
$90 pair |
Back to Top
|
| Please Note: Setup Charges for Tube Bases
A machining setup charge of $50 applies to all tube bases, however, if you order regular bases and extended bases at the same time, only ONE setup charge will apply.
|
|
|
|
Tube Bases
 Custom machined to fit your pipe or tubing, whether you use metric or Imperial sizes. Cast Aluminum with hardened and plated bolts. Two sizes are available depending on the size of your tube or pipe.
Minimum setup charge applies.
| Cat. # |
Quantity |
Price |
| CC-2400 |
1-10 |
$40 each |
| CC-940A |
11 or more |
$38 each |
|
 Extended Tube Bases
Custom machined to fit your pipe or tubing, whether you use metric or Imperial sizes. These are used on the outside of corners of platforms. Extends below bottom of platform for added support. Two sizes are available depending on the size of your tube or pipe. Cast Aluminum with hardened and plated bolts. Two sizes are available depending on the size of your tube or pipe.
Minimum setup charge applies.
|
